163 points by kusha 3 days ago | 70 comments | View on ycombinator
DannyBee 1 day ago |
blutack about 21 hours ago |
You can buy premade PCBs from a few open source projects to then connect the controller to Home Assistant etc. Because they speak to the controller over serial, they properly report the door position and can control the light as well as supporting partial opening.
I use this one: https://github.com/Gifford47/HCPBridgeMqtt and it's been rock solid for about a year now. It also has a temperature, humidity sensor and PIR sensor.
Also means you can then use Shelly BLE buttons or whatever as extra IP rated garage door openers.
VTimofeenko 1 day ago |
I paired it with Zen17, though in hindsight I could have just gone with an esp32 hidden right next to the motor.
Open/closed state is reported by a separate tilt sensor, which I might also swap for something else if only not to have to swap yet another battery
Namidairo 1 day ago |
One could just end up repacking the image with their own certificate chain, or patching out the reboot itself.
whatever1 1 day ago |
don-code 1 day ago |
This also makes me wonder why it's necessary. What requirement were they trying to solve for? Does lack of Internet connectivity mask some bigger problem with the firmware on the device periodically needing a restart?
Polizeiposaune 1 day ago |
doodlebugging 1 day ago |
Anyway, I decided based on the noises that it must involve something inside the garage. Good luck finding anything in there. I opened the door with the clicker remote and didn't notice any issues so I walked the "path" through all the accumulated things that needed new homes and as I was making my way back out the door I saw an unusual chunk of steel on the floor and a pulley that I know had not been there the last time I was in the garage. I began visually searching everything inside the garage trying to match those items found on the floor and that is when I saw the spring dangling on one side of the door and the lifting cables drooping.
That's when it hit me that I'm lucky our cars don't fit in there any more. All the energy stored in that spring when it popped could've cost me a couple of windshields, some body panel damage, etc but since my garage collects unfinished projects instead of automobiles all of the flying garage door parts bounced off of boxes and the sheetrock walls and did not damage anything important.
We briefly considered calling a garage door installer to deal with it so that we could replace both of the doors (two-bay garage). They had replaced a door on my shop a few years back and were reasonably priced and that Chamberlain door has functioned perfectly. Since the only parts compromised were the springs, pulleys, and cables on one side of the door I decided not to replace the door. There are spring kits available that allow a DIY replacement in a few hours so I went that route. Very inexpensive.
After reading comments here I am so glad I did not buy new doors. The last door we bought was produced before all the enshittified cloud crap. I replaced the remote panel controller this summer with a new, cheap control panel that looked identical on the outside but is slightly different internally since it is a generic replacement for the OEM part. Works great.
kusha 3 days ago |
The 819LMB is a HomeKit based device, meaning by HomeKit spec it is supposed to function 100% locally on your LAN with zero internet access. (most connect it to home assistant)
In their infinite wisdom, Chamberlain decided to cripple it anyway: if the garage door opener cannot reach their cloud, a firmware watchdog triggers a hard reboot every 30 minutes, taking down local HomeKit control along with it. Additionally, if you don't block the internet the right way, it reboots every 10 minutes in addition to the 30 minute reboot.
jmbwell 1 day ago |
tonymet 1 day ago |
I now only use MyQ as a last resort.
ProAm 1 day ago |
doctorpangloss 1 day ago |
God what fucking fuckwads
MalgorzataKowal 1 day ago |
bciuca 1 day ago |
Giving them money in the first place is a horrible idea.